Month: August 2015

Scanning i2c bus 6 on Intel Edison

In a previous post I discussed using the LMSensors project programs to scan I2C buses on the Intel Edison. As I mentioned in that post, I only had luck scanning bus 1 on the Edison (which is only available on the mini breakout board).

Generally, when using i2ctools to scan bus 6 on the Edison the scan will run very slowly and no devices will be found. I have been a little confused by this in the past because occasionally I would find that I am able to scan the bus normally with those tools. I even went so far as to create a tool using the MRAA libraries to implement similar functionality with a Nodejs script. But I have found something interesting.

What I found was that i2c bus 6 is not configured when the system is started. If I have a node application running that uses i2c (which most of mine do) I find I am able to scan the bus with i2c tools without a problem. Also my tool — m2ctool — can serve to configure the bus so that it can be accessed by i2ctools.

To see what I am talking about try this:

  1. Start up your Edison and login. Ensure no programs are running.
  2. Enter the command i2cdetect -r 6. Press enter when prompted.
  3. The bus should scan very slowly and show no devices.
  4. Download and install m2ctool. See instructions on the read me to install.
  5. Enter the command m2ctool scan 6.
  6. The bus should scan normally and show any devices that are installed.
  7. Enter the command i2cdetect -r  6.
  8. The bus should scan normally and show any devices that are installed.

So if you need to probe i2c bus 6 on Edison but don’t have a program running that utilizes i2c, just run ‘m2ctool scan 6’ and then use i2ctools as you normally would. I have only tried this on Edison, I don’t know if this is true on other MRAA based systems.

The m2ctool has other features, I had intended it to stand in for i2ctools when dealing with MRAA based i2c buses. But given that all I need to do is initialize the bus by running a program once I could have saved myself a bit of work. For more info on m2ctool see the read me in the git hub repo.

Using a Rotary Encoder on Intel Edison, XDK

Rotary Encoders are supported by the UPM library. There is already example code that can be leveraged when we want to use one.  The code was created for the Grove Rotary Encoder but in reality we can use it for any rotary encoder we choose to implement. The Grove encoder  would be a good choice if you are using Seed Studio’s Grove Starter Kit. But that could be a problem if we wanted to use the encoder on and Edison project for the mini breakout board or wanted to access the switch in the encoder (you can not access the switch in the Grove Encoder). In my case, I intend to use the encoder to drive a menu for controlling an Edison on a mini breakout board. To accomplish that I will need to have access to the encoders built in switch so I will roll my on implementation.

Since we are going to use the Grove library for the encoder we will implement ours like theirs. If we look at the schematic for the Grove encoder we can see that it is not really that complicated.

Grove Encoder Schematic
Grove Encoder Schematic. Don’t connect  4 and 5 of the switch this way.

We can also see why the switch is not available on the Grove device – not enough pins available on the connector. (Though it does look like activating the switch will pull SIGA down, which we could look for in code. But the UPM library for this doesn’t have any provision for it.) We will wire up our encoder this way but we will wire the switch a little differently.

For the switch we will wire it so the we get a high value when it is actuated. So pin 4 goes to ground via a 10k pull down resistor and to the signal in for our Edison. Pin 5 will go to VCC.

So we need:

1     Encoder — I used these: 360 Degree Rotary Encoder w Push Button

1     Ceramic Disk 100 nf Capacitor (that is 0.1 micro farads, marked 104 on the cap).

4     3.3k Resistors. I used 2% 1/4 watt.  

And for the switch:

1     10k Resistor – also 2% 1/4 watt.

Optionally:

1     Arduino stackable header.  I plugged the encoder into this so it would fit in a breadboard better.

Wiring it up on a bread board gives us something like this:

Wired to a bead board side view
Side view
IMG_20150814_175210
Overhead view
Connected to an Edison Arduino.
Connected to an Edison Arduino board.

I used my Edison Arduino Board to prototype this, so the connections are:

SIGA —> D2

SIGB —> D3

Switch ( encoder pin 4) —> D4

VCC –> 3.3 Volts.

Don’t forget the ground connection.

The code to test this is pretty simple since we are using the UPM Libraries. We will use the Grove Rotary Encoder library for, of course, the encoder. We will use the Grove Button Library for our button functionality.

We will use socket.io to monitor our encoder with a webpage. Our server code looks like this:

//Setup express 
var express = require('express');
var app = express();
app.use(express.static(__dirname));
var server = app.listen(8085);
var io = require('socket.io').listen(server);



var mraa = require('mraa'); //require mraa
console.log('MRAA Version: ' + mraa.getVersion()); //write the mraa version to the Intel XDK console

//var myOnboardLed = new mraa.Gpio(3, false, true); //LED hooked up to digital pin (or built in pin on Galileo Gen1)
var myOnboardLed = new mraa.Gpio(13); //LED hooked up to digital pin 13 (or built in pin on Intel Galileo Gen2 as well as Intel Edison)
myOnboardLed.dir(mraa.DIR_OUT); //set the gpio direction to output

//Require the encoder and button libraries. 
var rotaryEncoder = require("jsupm_rotaryencoder");
var groveSensor = require('jsupm_grove'); 
// Instantiate a Grove Rotary Encoder, using signal pins D2 and D3
var myRotaryEncoder = new rotaryEncoder.RotaryEncoder(2, 3);
//Set up a button on D4
var button = new groveSensor.GroveButton(4); 
 
//We will send data to our client with this object. 
var data = {}; 

//When we get a socket connection we will monitor the switch. 
io.sockets.on('connection', function (socket) {
 
 //Every 100 milli seconds we will send an update to the client. 
 //You won't want to monitor encoder this way for a real project
 //but it will demonstrate the encoder and switch. 
 setInterval(function () {
 //See what the switch value is.
 readButtonValue(); 
 //Sample the current position of the encoder. 
 //Since this is an incremental encoder we will
 //get increasing or decreasing int values from 
 //the encoder library. 
 data.position = myRotaryEncoder.position();
 //For the porposes of this demo, if we go lower than -40
 //or higher than 40 we will reset the encoder init to 0. 
 if(Math.abs(data.position) > 40 ) {
 myRotaryEncoder.initPosition(0);
 data.position = 0; 
 }
 //Send the position in a json encoded string. 
 socket.emit( 'position' , JSON.stringify(data));
 }, 100);

 //Toggle the on board led on or off. 
 socket.on('toggle_led', function(data){
 if(data === 'on'){
 myOnboardLed.write(0);
 } else {
 myOnboardLed.write(1); 
 }
 });
 

});

//A fuction to read our button value
function readButtonValue() {
 //If our button is pressed set the 
 //encoder init to 0. 
 if(button.value() === 1 ) {
 myRotaryEncoder.initPosition(0); 
 } 
}
 


// When exiting: clear interval and print message

process.on('SIGINT', function()

{

 clearInterval(myInterval);

 console.log("Exiting...");

 process.exit(0); 
 
});

A Github repo with working code is located here.

When you load this on your Edison and browse to the web page it will look something like this:

Or demo page contains a gauge the reads from -40 t- 40.
Or demo page contains a gauge the reads from -40 to 40.

Rotating the knob on the encoder clockwise will increase the reading on the dial. Counter clockwise will decrease it. Activating the button on the encoder will reset the dial to 0. If we go below -40 or above 40 the dial will reset to 0. This code is based on the socket.io demo I posted about previously.

So there we have it. Using a rotary encoder in our projects will give us the ability to add controls with out the need of using potentiometers and switches. With an encoder we can implement multi-level menus to enable our end users to configure and control our devices even if they are not connected to wifi or a usb port. Implementing a menu such as this will be the subject of an up coming post.

Implementing the MICS-VZ-89T gas sensor on Intel Edison i2c

On my current project I have the requirement to monitor indoor air quality. What is of interest are the levels of Volatile Organic Compounds (VOCs) and CO2.  There are specific thresholds that we are looking for that when exceeded should trigger an action. For VOCs it is when the concentration is greater that 0.9 ppm. For CO2 it is when the concentration is 1000 ppm above ambient out side C02 — which is generally around 400 ppm. The links above out line the dangers of these indoor pollutants. When the threshold is reached we want to start the ventilation system and optionally message a user.

When I need a sensor my first choice is to find one that implements i2c. In this case I found a good candidate for the job in the SGX Sensortech MICS-VZ-89T. The VZ89 product is a small board with a MICS SMD device integrated with an i2c controller. The board comes in both 5 volt (VZ89) and 3.3 volt (VZ89T) versions that are are easy to implement using a logic level shifter with the Edison on a mini breakout board. (For an example of using a logic level shifter you can see my article Intel Edison and I2C sensors with XDK.)

There was no driver that I could find for implementing the board with my setup so I had to roll my own. This wasn’t too hard, but I did have to break out the logic analyzer to get it right. If we examine the MICS-VZ-89T I2C Specification page  we see that the device only has two commands. These are Set ppmC02 and Get VZ89 Status. According to the MICS-VZ-89T Data Sheet the device comes calibrated from the factory so we don’t need to implement Set ppmC02. That leaves us Get VZ89 Status. The code that follows here is available in an XDK project on git hub.

To read the status we have to perform a two step process. First we write a command byte of 0x09 to register address 0x70. We follow this by writing two data bytes to the same register. I write 0x00 twice.

We then read 6 bytes immediately after writing the command byte. The bytes are decoded as follows:

Data byte 1 = CO2-equivalent value. 
Data byte 2 = VOC_SHORT value. 
Data byte 3 = VOC_LONG value 
Data byte 4 = Raw sensor 1st byte (LSB). 
Data byte 5 = Raw sensor 2nd byte 
Data byte 6 = Raw sensor 3rd byte (MSB).

To implement the functionality I created the following class in a node module:

//Import mraa 
var mraa = require('mraa');

//Constructor -- set defaults and populate tx_buf
function VZ89(bus , address){

 this.bus = new mraa.I2c(bus || 1); 
 this.bus.address(address || 0x70); 
 
 this.tx_buf = new Buffer(3); 
 this.tx_buf[0] = 0x09;
 this.tx_buf[1] = 0x00;
 this.tx_buf[2] = 0x00; 
 
}

//Add a function to get the device readings. 
VZ89.prototype.getReadings = function() {
 this.bus.frequency(mraa.I2C_STD);
 this.bus.write(this.tx_buf); 
 return this.bus.read(6);
 
};
//Export as a node module 
module.exports = VZ89;

The MRAA library is used to access the i2c bus, so it is imported at the top or the file. There is a constructor that optionally takes a bus number and a devices address. The VZ89 is addressed at 0x70 so we don’t really need to change that. If the Edison mini-breakout is used we have a choice of busses. I have set this to bus 6 as I am using the Edison Arduino for this example.

A class function is added to implement named getReadings to perform the measurements and return data from the device. In this case the buffer is passed back to the calling program for use.

To use the class the code in the server file would look like this:

//Import our sensor file from the file system
var Sensor = require('./VZ89.js'); 
//Create an instance of the sensor object. 
var sensor = new Sensor();
//Create a var for the receive buffer.
var rx_buf; 

//Call the readBuf function every minute. 
setInterval(readBuf , 60000); 

//A function to read the sensor data, perform data conversions and display on the console every minute.
function readBuf(){

    rx_buf = sensor.getReadings();
 
    console.log("Co2_equ: " + ((rx_buf[0] - 13) * (1600/229) + 400) + " ppm"); 
    console.log("VOC_short: " + (rx_buf[1])); 
    console.log("tVOC: " + (rx_buf[2] * (1000/229)) + " ppb"); 
    console.log("Resistor Value: " + 10 * (rx_buf[3] + (256 * rx_buf[4]) + (65536 * rx_buf[5])) + " ohms"); 
}

The details of converting the rx_buf data to usable values are in the data sheet.  The ones we are most interested in are Co2 equivalent (rx_buf[0]) and total VOC (rx_buf[2]).

As you can see, the MICS-VZ89T is a pretty easy to use device once you know how. There are only a couple of gotchas to be aware of. First, the device can only be polled once a second. I find if I try to get the readings faster than that the device will return nulls. Secondly, care must be taken when handling the device. It contains organic material that is susceptible to solvents.

Nodejs, Socket.io and Intel Edison

One of the things I really like about the Intel Edison (and the Galileo) is that they can be run as little Linux computers. We can use a lot of tools that are available for Linux machines. One of those tools in particular is nodejs.

Nodejs is a very powerful server side platform. It comes preinstalled on the Edison and Galileo Yocto images so it is very easy to get started with. We can implement code on the Edison and Galileo with the Intel XDK IoT Edition. With this combination of tools it is very easy to create applications that can monitor and control a remote Edison via a web based interface.

To get started I have created a repo on Git Hub that contains a project for the XDK. This project utilizes several technologies — node js, express , socket.io and  mraa library  on the server side. Jquery and an open source library to implement a gauge are used on the client side. I will be using the MCP9808 setup that I blogged about previously but any sensor (or group of sensors) could be utilized.

Before we jump into the code lets make sure we our Edison in up to date. I am using version 146 of the stock Yocto image. To check the version of your Edison execute the following:

configure_edison --version

If you need to update your Edison you can use the following:

configure_edison --upgrade

If you upgrade your Edison you will have to set up the wifi again.

To install the code on your Edison use the Intel XDK to open the project downloaded from Git hub. If you are using the Edison Arduino board open app.js and change line 23 to use i2c bus 6. Upload the project and use the build action to install all the Node dependencies. If you had an app running on the Edison previously you will need to stop it and start this one with the start and stop buttons.

The server code is located in the root of the project in the app.js file.  Here are lines 6 thru 10:

6  var express = require('express');
7  var app = express();
8  app.use(express.static(__dirname));
9  var server = app.listen(8085);
10 var io = require('socket.io').listen(server);

The first  four lines set up Express. Express is a full featured web framework for Node, but here I am just going to use it to serve up my static files from the file system.  The static server is set up on line 8. Line 9 instructs our server to listen on port 8085. Socket.io is initialized on line 10 and instructed to listen for connections on line 10.

Express may seem like overkill for this application, but I like to use if because it is easy to configure and is well supported. There are other, lighter foot print modules that can be used. You can find these other http servers by looking in the NPM Registry .

The real work in the server is done on lines 28 thru 44 :

28 io.sockets.on('connection', function (socket) {
 
30  setInterval(function () { 
31 socket.emit( 'temp' , JSON.stringify(getTemp())); //send temp every interval
32 }, 2000);

35 socket.on('toggle_led', function(data){
36   if(data === 'on'){
37     myOnboardLed.write(0);
38   } else {
39     myOnboardLed.write(1); 
40   }
41 });
 

44 });

Line 28 sets up socket.io to listen for connections. Each client connecting to this device will start the callback that sends the current temperature every 2 seconds (lines 30 – 32 ) and listen for the ‘toggle_led’ event (lines 35 – 41) to allow an led to be turned on and off.

The client side code is just as simple. The index.html page contains divs that hold the guage and a button.  The javascript code that does the work is in /js/app.js . This is all pretty standard stuff, but the first time I worked with socket.io I was stumped for awhile trying to find the source file for the socket.io client (Line 11 in index.html). This file is served automatically from our node server when we run it and is included in the server side socket.io code. All we need to do is add the line to load it in index.html.

If we look at the client side javascript in /js/app.js :

1  var socket = io.connect();
2
3  socket.on('temp', function (data) {
4    var status = JSON.parse(data);
5    Gauge.Collection.get('temp').setValue(status.farenheit); 
6   });
7
8  function toggle_led(state){
9  
10   socket.emit('toggle_led' , state ); 
11   var button = $('#led_button'); 
12   if(state === 'on'){
13      button.attr("onclick", "toggle_led('off')"); 
14      button.html('Turn off led'); 
15    } else {
16      button.attr("onclick", "toggle_led('on')"); 
17     button.html("Turn on led");1
19    }
20 }

We see that the code is fairly simple as well. The socket.io client is initialized on line 1 with a connection to the server we loaded our script from. We then setup a listener for the “temp” event on line 3. If we get a “temp” event the callback function will parse the json string from the server and update the guage in our page to the current value of our MCP9808. (Check the guage git hub page for comprehensive details on its use.)

To toggle the onboard led we have implemented the function at line 10 to emit the “toggle_led” event to the server. We also swap out the events on the button so we can just use one button to toggle the led.

The thing to remember is that the socket.emit sends an event with the name that we provide (in this case “toggle_led”). We need to ensure that the listener for this event uses the exact string. I’ve messed this up a couple of times.

It should look something like this when we have it running:

When the page is running it will look something like this.
When the page is running it will look something like this.

So there you have it. We have implemented a simple web page on the Edison so that we can get the temperature from out MCP9808 and display it. We have implemented the ability to toggle an led on the Edison from the web page. These examples are pretty basic, but the demonstrate a good starting point for more enhanced functionality that could be implemented. Feel free to use the template as a starting point in your projects.